Lived on-board Hadar

Daisypath Vacation tickers

Monday, May 22, 2006

Week Twenty














Monday 15th May 2006.
Steve 1 had out the newspaper and masking tape and set about masking up the gunwales, and the open hold ready to spray paint them in what can only be described as chocolate brown mmmmmm and lovely it looked to. You can certainly understand why they wear masks whilst spray painting the smell of the fumes is enough to send anyone high. I have to say though it did nothing for me. But I do love the colour.

Tuesday 16th May.
No work done on Hadar today.

Wednesday 17th May.
Roger began work on the holds woodwork, the planks, mast and stand. His first job was the rear cross member, he then made the top plank block which sits on the cabin roof, he also started on the stand.

Thursday 18th May.
Roger spent the day making up the stand, he put them in place with the cross member. He also made up the mast box and then arranged the top planks and cross member.

Friday 19th May.
No work today done on Hadar, they are waiting for the tongue and groove wood to arrive for the cratch.













Over this past week Keith has enjoyed helping Roger with the woodwork, helping with measurements and the carrying of the timber, which is very substantial. The planks alone vary in length, but are 1 ½ thick by 11 inches wide. We are now getting very close to Hadar’s launch. Once the timber work for the hold is done, Roger can measure up for the sheeting. That can be got then fitted and yayyy we get to launch. We cannot launch until the sheeting is fitted. Because if it rains and the hold fills up she will sink Eckkk as there are no drain off holes in the hold. Anyway another week of activity and plenty more to come so please keep popping in for a read and a look at the photographs.

Monday, May 15, 2006

Weeks Eighteen and Nineteen














Monday 1st May 2006.
No work today as it was the May Day Bank Holiday.

Tuesday 2nd May.
Outlets were cut for the drain holes, for the basin, shower and galley sink under the port side window in the galley. The outlet for the washing machine was cut on the starboard side. The battening out continued ready for the foam insulating, which was booked for Wednesday. Once the battening was completed, all holes ie: port holes, chimneys, drain holes, etc were covered and sealed ready for the foaming. Holes were also cut through the bulkheads to take water pipes and electric cables, they were then covered and sealed. Also all the battening had to be covered with tape, so that once the foaming was done the tape could be taken off to reveal the wooden batten. The bulkheads in the engine room were covered with newspaper and taped up, they are not insulated as they only need insulation one one side only. Steve 2 had the messy job of rubbing down the cabin tops read oxide coat, ready to take a coat of gloss, so Hadars body work will be protected once outside. A top coat of gloss is added because the red oxide alone is porous. Once Hadar is ready for her final paint job, all this will be stripped off.

Wednesday 3rd May.
The guys from A & K Insulations Ltd (
www.insulationsprayfoam.co.uk) arrived around 8:15am and prepared their equipment for the task of insulating Hadar's cabin. James was doing the spraying whilst John his partner was in charge of looking after the pumping equipment. They had to make sure there was at least a 1" even coat of foam through out the boatmans cabin, bathroom, galley and saloon. They finished it around 11.45am and then set about packing everything away.

Thursday 4th May.
There was no work done on Hadar, as Steve 2 had injured his ankle, and was taking a few days off to recover.

Friday 5th May.
Steve 1 started to clean the battens after completion of the foam insulating, where the spray foam had come into contact with them.
*********************************************************************************













Monday 8th May 2006.
Steve 1 continued the job of stripping back the foam insulation off the wooden battens. He also had the job of cutting back and sawing off the excess foam, where it was protruding over the wooden battens. I found that the sawing of the foam put my teeth on edge ewwwwww.


Tuesday 9th May
Steve 2 is still off work, with torn ligaments in both sides of his ankle, we wish him a speedy recovery. Steve 1 was again cleaning the battens this time in the boatmans cabin. Once that was all done he then painted the floor in the boatmans cabin.


Wednesday 10th May
Steve 1 finished rubbing down the cabin top that Steve 1 had started before his ankle injury.


Thursday 11th May.
No Steve 1 today he hurt his back on Wednesday. The mast and stand timber arrived. We sat down and worked out where we want all the electric sockets and lighting fitted.


Friday 12th May.
Steve 1 was back, all be it a little stiff, he finished rubbing down the cabin top. He then altered the sheeting fixing rail. Finally for this week he spray painted a coat of ice blue gloss paint over the red oxide. The gloss coat is there to protect the metal work, once outside until the final painting.

Tuesday, May 02, 2006

Weeks Fifteen, Sixteen and Seventeen

Monday 10th April 2006.
Hadar was lowered back to the shed floor, back on safe ground. Steve 2 was back on rivet duty, and it was the turn of the roof edge, doors and bulkhead. These rivets were much smaller than the hull rivets, so much more fiddly to put on and weld, in fact I think Steve had the patience of a saint. All in all on the Starboard side he welded on 221, see what I mean the patience of a saint.
Tuesday 11th April.
Steve 2 was again on rivets, this time on the port side, and in all he welded on 231 on the cabin tops doors and bulkhead. Believe it or not I actually counted all the rivets after he welded the remaining bow rivets on and amazingly there are approximately 1315. I say approximately because after counting them all twice I was ginging up the will to live. So if we meet up on the cut and you want to challenge my total feel free to count them up Ha ha ha. Believe me it is not easy, I was seeing double by the end, so goodness knows what it like to have to weld them all on. I will apologise to Steve 2 right now for putting him through that torture LOL... Oh heck I was forgetting he got paid to do it LOL. Steve 2 also fitted 4 fold up brass foot steps which are on each corner of the cabin top. So when we are both to old to climb onto the cabin top we can use the steps. Don't laugh we have to think of these thing's now after all I am coming up for 44 LOL. We maybe spring chickens now but as Hadar is going to be our only boat built from new, we are having everything fitted now for our more advanced year's. Forward thinking pay's, so if your thinking of having a boat built, think about what will happen when you are getting older and what you would like fitted now.Back to the boat, I was getting side tracked. Roger begain working on the swan neck, he had the steel on the lathe. Now that was an interesting thing to watch, look at the photo's and the one with the hole in the wall where the steel pole comes out. A great bit of design work LOL.


Wednesday 12th April.
The letter box vents for the boatmans cabin were screwed into place on both sides of the cabin top. When the boat's were first built with them in the 30's, the vents were open and used, but on our boat they will just be for affect. It all just adds to the over all affect. Steve 2 also welded into the open hold the mast base box, which will take the main wooden mast.


Thursday 13th April.
Steve 2 added more framing out steel in the cabin around the port holes. Both Steve 1 and Steve 2 then stated the bending of the swan neck, using a blow torn and brute force.
Friday 14th April. Good friday so nothing happened today it was a well earned day off for everyone.


********************************************************************************

As it was the Easter Weekend no body worked Easter Monday 17th April.

Tuesday 18th April 2006.
Back to work and the swan neck was made, fitted and painted with red oxide. The screw holes for the navigation lights were drilled in to the saloon bulkhead. The head lamp post was welded into place above the gas locker at the bow.


Wednesday 19th April.
Steve 2 was busy with grinding back of the hull. Ariel fixing points were drilled out on the roof. Roger sorted out the gearbox, which had been in one of his previous boats, it had had very little use. The Top Hat was made and fitted on to the rudder post, above the rudder tube.


Thursday 20th April.
Steve 2 started spraying our cabin top and roof with red oxide paint. The fumes alone were enough to make anyone high LOL.Roger cut out the battens, for the framing out of cabin. Steve 1 cut out and welded the plate to the gearbox, that will hold it all in place.


Friday 21st April.
Steve 2 all masked up finished spraying the boat, doing the open hold and the bow, then both he and Roger began blacking the bottom with 2 pack. Hadar will have 2 1/2 coats of the 2 pack.

**********************************************************************************

Monday 24th April to Friday 28th April we were away. You can read about the fun few day's we had at http://www.ladyjogearman.blogspot.com/ Work was still taking place on Hadar over the week and it was as follows.

The port holes for the cabin top and pigeon box arrived along with their glass. The bulls eye also arrived along with the mushroom vents. All the holes were drilled into the cabin top to take the afore mentioned. The battening timber was screwed into place through out the boatmans cabin, engine room, bathroom, galley and saloon. The sheeting eyes were welded into place along the gunwales of the open hold. They will hold the ropes in place over the sheeting. 2 vents for the diesel were put into place in the walls of the engine room. The day tank was also fitted into the engine room. We discussed the outlets for the shower, basin, galley sink and washing machine with Roger. The yellow Pine for the open hold top planks arrived they are each 11" x 2". So it was a very busy week whilst we were away.